The is a rear double cup holder made for the 1996-2002 3rd Generation Toyota 4Runner. It is made of ABS plastic through the use of a 3D printer. It comes in the two factory colors of Tan and Gray. It can hold most beverage containers on the market. The inside diameter of the holes is 3″ so anything inside that diameter will fit. The flimsy factory rear cup holder will need to be removed first. There are two screws that hold the factory pull out cup holder in place. Once you pull it out you will be able to see and access them. Those 2 screws will not be reused. The new much stronger cup holder will come with 2 new longer screws. The cup holder should slide right into the hole left behind from the factory cup holder. You will need to apply force across the bottom to “click” the cup holder into place. Make SURE you here/feel the cup holder click into place. It has a locking tab underneath that will help secure it onto the console while you thread in the two screws. Remember that you are threading into plastic tabs and not metal. The screws can easily crack those tabs if you over tighten them. Get them snug and then stop turning. You can also use the 3M adhesive strip for added insurance but that is not a must.
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
This is a double cup holder insert for the 60 Series Toyota Landcruiser. This cup holder is made of ABS plastic. It comes in a black satin finish. It will hold 2 cups, a cell phone, and 2 pens. There are strips of 3M adhesive installed on the bottom to stick it down into the hole. There are also 2 self taping screws provided. You can use the adhesive only or the adhesive and screws; depending on how secure you feel you need it.
This is a double cup holder insert for the 62 Series Toyota Landcruiser. This cup holder will hold two cups, two phones, a wallet, a pen/pencil, and a flashlight. It is designed to fit the transmission hump in front of the center console. It will lay flat on the hump and match the contours of the 60 series interior. This is made of ABS plastic with a black satin finish. It will come with strips of 3M adhesive installed and 4 self taping screws. You can use the adhesive only or the adhesive and screws; depending on how secure you want the cup holder.
This is a single cup holder for the 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. The cup holder will hold any fast food cup and most beverage container sizes. If you remove the black insert then you have a much larger diameter cup holder for items like a Nalgene bottle. The cell phone slot 3.25″ across and .65″ deep which will allow for most larger cell phones on the market with a case. There is also a pen holder. This single cup holder DOES allow for almost full movement of the passenger seat front to back. You lose about 1/2″ of forward movement which is very minimal. You could push the cup holder forward to allow for full movement of the seat but that would cause the larger fast food cups to come in contact with the dash but that is also minimal. This is available for the automatic and now manual trans. Install Instructions There are 3 strips of 3m automotive adhesive already installed. This is the primary method of attachment. Make SURE the console is cleaned really well before you attach and use good force when attaching. The cup holder will not bond well if the console is not clean. 2 screws are also included to be used in the 2 screw holes. The screws are an added insurance to ensure the cup holder is secure. I would highly encourage you to use the screws. Use a small drill bit and predrill the holes once the cup holder has been stuck into place. Then use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Also, do not over tighten them by hand. Turn the screw until it is snug and then stop.
This is a single cup holder for the 84-89 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot that is 3.5″ wide which will accept just about every major phone style available. There is a notch at the bottom of the cell phone slot to allow a charging cable to be ran up from the bottom. Be aware you will need to cut a hole in the bottom on the console to be able to run the cable. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There is a countersunk hole at the bottom in case you want to screw it in. That is not a must, just a preference. Any 3/4″- 1″ coarse thread screw will work. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only. Be aware that there are 4 different consoles that came on the 1st gen 4Runner and this insert will only fit in two of them(which do seem to be the more popular options). Make sure to look at the pics to make sure they match your console.
This is a 8″x2″ machined aluminum TOYOTA retro badge. It was made to closely resemble the TOYOTA logo found on FJ40’s and other early Toyota trucks and SUVs. It has 3 recessed slots on the back for 3 long strips of 3M automotive adhesive. It will stick flush to any flat surface on any Toyota truck or SUV. It is available in black, red, and cream. The letters will have a brushed aluminum finish. More pictures are coming soon of the other colors.
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.
This is an accessories panel for the 1996-2002 Toyota 4Runner. It mounts to the center console. This is made by a 3D printer from ABS plastic. This will accept OEM Toyota switches from 95-02 and some aftermarket switches. There are two options which is the 4 hole plate and the 2 holes plate. Install instructions will be provided with the packaging. Blank plug inserts can be ordered separately if you want 4 holes but only have 2 accessories so far and don’t want to have an ugly hole for a time period.
This is a rear cargo area accessories plate that replaces the OEM 12 volt accessory panel found on the 99-02 4Runner. This can be mounted to the 96-98 4Runner but the hole will need to be cut and a new 12VDC 10A power supply will need to be ran. This plate is made from ABS plastic by a 3D printer. There are two versions available. There is design #1 which has 2 accessory 12 volt holes/plugs, 1 OEM window switch hole (window switch not included), and one 12 volt meter display. There is also design #2 which has 3 12 volt accessory holes (no window switch hole), and a 12 volt meter. Please be aware the top right corner MUST be the 12 volt meter due to the shallow design of that accessory. Behind the plastic interior wall is a metal plate in that location and a full depth 12 volt accessory plug will not fit. The other 3 accessory locations do not have anything behind it and any 1″ accessory plug can be mounted there. You can order this as the plate only OR fully set up with all accessory plugs pre-installed with connectors and a spool of wire. Running and connecting wiring is done by the customer.
This is a 3D printed double cup holder for the 1996-2002 Toyota Hilux Surf. This will work on the 4WD automatic console. This will NOT fit on the manual transmission console. That design in still in development. This cup holder is made of ABS plastic and comes in flat black only. This design one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. This design will hold just about any container on the market. Be aware, this design prevents full forward movement of the passenger seat. The front 3″ of movement will be blocked by the cup holder.
Install Instructions
There are 2 strips of 3M automotive adhesive already attached to help with install. Make sure the surface attaching to is totally clean. Once stuck in place with the adhesive then you will want to use the 2 provided self-taping screws in the side and top hole. Use a hand screw driver and not a power drill so you don’t strip the hole.
This will fit in the 1989-1994 Toyota pickup console. This was mostly offered in the SR5 model. This is 3D printed from ABS plastic. No hardware or tools are needed to install. This will NOT fit in the 4Runner from the same years. That is a different console and we make a different cup holder for the 4Runner console.
This is a machined aluminum “Turbo” badge that mounts to the 70 Series Landcruiser grille. This does NOT fit on all years 70 series cruisers. Please look closely at the pics to ensure the picture matches your grille. This is attached with 3M badge/decal foam adhesive. No screws are needed and no modifications to the factory grille are needed.
This is a machined aluminum badge with a satin brushed finish on the lettering. This is not a plastic replica like the OEM badge was. This badge is an exact match in size to the original factory badge and mounts with strips of 3M automotive badge/decal adhesive. No drilling of the fenders is needed. The overall length is exactly 10″ (254mm) by 1.4″(36mm) tall. This badge will fit in the factory fender location of the 1979-1983 Toyota pickup BUT it can also mount to any flat surface of any Toyota. It can be mounted on a surface like a flat tailgate of a more modern vehicle giving it that old school retro look.
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
This aluminum TEQ badge mounts onto the front grille of your 2011-2015 Toyota Tacoma. It replaces OEM part #90975-A2001. The size is 6.25″ x 4.25″ (159mm x 108mm) The factory chrome badge must be removed. The factory mounting holes will not be used on the new badge. To remove the factory badge simply pry it off. It is held on with plastic tabs. No adhesive or screws were used. The new badge is held on with 3M automotive decal adhesive. The surface on the grille the new badge will mount to MUST be cleaned before mounting. This badge comes in the common black/silver color, red/silver color, and in raw metal (no paint or primer) for folks who want to do their own custom paint job.
This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.
This is an aluminum diesel badge. It comes it two options. You can order the grille badge that comes with a backing plate pre-attached to allow it to mount flush to the curvature on the grille of the 70 Series Landcruiser OR you can order it without the backing plate as a flat universal mount badge that can be mounted to any flat surface on the vehicle. It has a satin black finish with brushed aluminum raised letters. The OEM screw pegs are not present on our badge so that the badge can mount to 70 series grilles that did NOT come with the holes for mounting. Our badge mounts with 3M automotive badge adhesive. It’s plenty strong to hold the badge for many years without issue as long as the surface is thoroughly cleaned before install. No drilling of the factory grille is needed. Simply peel back the glue backing and stick it on.
This is a single cup holder that mounts onto the driver side of the console. It is a standard 3″ diameter hole which will hold the usual fast food cup, soda can, and grocery store water bottle. It will not hold the larger Hydroflasks, Yeti’s, and Nalgene bottles. Our passenger cup holder can do that. The driver side cup holder had to be smaller to account for the drivers leg and shifter levers. This attaches with 2 strips of 3M adhesive and 2 self tapping screws. It is made of ABS plastic with a 3D printer.
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.