80 Series/LX450 Double Cup Holder
3rd Gen 4Runner Double CupHolder 96-02
This is a double cup holder for the 1996-2002 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. This design is for the automatic 4WD and 2WD versions. It will NOT work on the manual transmission console. Our single cup holder design has an option for the manual tranny. The larger hole has an insert which holds large fast food cups. With the insert removed it can hold large water bottles like a Nalgene and Hydroflask bottle. The smaller cup holder can still hold large fast food type drinks snugly but can also securely hold small diameter containers like a soda can, small drink, and grocery store water bottles. There is also a cell phone slot on the passenger side that can handle almost all phones on the market. There are also two pen holders. This cup holder does NOT allow for full movement of the passenger seat. There is about 4″ of forward motion lost but the seat can still go back almost 6″ without issue. If full motion of the seat is extremely important to you then order the single cup holder which allow for that movement. Install Instructions There are 4 strips of 3m automotive adhesive already installed. Make SURE the console is cleaned really well before you attach and use good force when attaching. 2 screws are also included to be used in the 2 screw holes. The shorter silver screw goes underneath the black insert and the longer black screw goes in the lower side hole on the passenger side. Use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Turn the screw until it is snug and then stop.
3rd Gen 4Runner Single CupHolder 96-02
This is a single cup holder for the 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. The cup holder will hold any fast food cup and most beverage container sizes. If you remove the black insert then you have a much larger diameter cup holder for items like a Nalgene bottle. The cell phone slot 3.25″ across and .65″ deep which will allow for most larger cell phones on the market with a case. There is also a pen holder. This single cup holder DOES allow for almost full movement of the passenger seat front to back. You lose about 1/2″ of forward movement which is very minimal. You could push the cup holder forward to allow for full movement of the seat but that would cause the larger fast food cups to come in contact with the dash but that is also minimal. This is available for the automatic and now manual trans. Install Instructions There are 3 strips of 3m automotive adhesive already installed. This is the primary method of attachment. Make SURE the console is cleaned really well before you attach and use good force when attaching. The cup holder will not bond well if the console is not clean. 2 screws are also included to be used in the 2 screw holes. The screws are an added insurance to ensure the cup holder is secure. I would highly encourage you to use the screws. Use a small drill bit and predrill the holes once the cup holder has been stuck into place. Then use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Also, do not over tighten them by hand. Turn the screw until it is snug and then stop.
80 Series (95-97) Dash Bezel/Cell Phone Mount
This is an accessories dash bezel for the 80 series (95-97) dash. There is only one type of bezel that accepts all the different options. This will also fit the LX450. This is made of ABS plastic and will allow you to add two more accessories like OEM and Aftermarket buttons/switches, CB mic holder, cell phone holder, single 1″ RAM ball, and a double 1″ RAM ball. If the dash came with the factory pull out single cup holder then that will need to be removed. If there is a black plastic hollow insert/cubby instead of the pull out cup holder then the insert will need to be removed and discarded. The holding tabs for the factory insert are at the top. You need to compress them to pull out the insert from the dash. Reuse the two factory screws in the dash that are behind the cover to install the bezel. The cell phone holder will come with an additional 4 screws for mounting. You can also add a plug or two if you do not have two accessory buttons yet. There is also a CB mic holder that can be placed in one of the holes. The cell phone mount, plugs/inserts, RAM Ball, and CB holder are an extra cost. The finish of the bezel and inserts are a satin black to match the other black parts on the dash.
1st Gen 4runner Single Cup Holder
This is a cup holder for the 1st gen body 4runner. It is for the manual transmission set up ONLY. It will hold just about any fast food cup size drink with the insert installed. With the insert removed it can hold a large sports (Nalgene) bottle. There is also a pen holder and cell phone holder. The inside width of the cell phone slot is 3.25″ That should accept just about any cell phone on the market including the new IPhone6 plus. There are two avialable colors: the dark gray or black. Both colors come in a satin/flat finish. Installation: There are two strips of 3M automotive adhesive underneath the cup holder to aid in attachment. There are also 2 screw holes located at the bottom of the cell phone tray and on the bottom outer edge. Two self taping screws are provided. No drill bits or power tools are needed. Just thread the screws into the plastic with a handheld phillips screw driver. They will drill themselves into the plastic. Do NOT over tighten. You are threading into thin plastic. Thread the screws in until they are snug and stop.
2nd Gen 4Runner Cup Holder Console Insert
This is a single cup holder for the 90-95 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot on the back that is 3.5″ wide which will accept just about every major phone style available. There are also two round holes to accept pens and two rectangular holes to accept a knife, leatherman, lighter, etc. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.
(91-94) 80 Series Dash Phone Mount
This is a dash mounted cell phone mount for the 91-94 80 Series Landcruiser. At full width it’s just over 4″ wide. The lower mount is 3D printed out of ABS plastic. It is held on with 2 strips of 3M automotive adhesive and 4 self taping 1/2″ screws. You can use a power drill to drill/thread the screws in BUT use a hand screwdriver to tighten them down the last little bit. Tightening down the screws with a power drill may crack the dash or strip the hole.
1st Gen 4Runner Double Cup Holder
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.
1981-1984+ 40 Series Double Cup Holder
This is a double cup holder for a 1981-1984+ FJ40 Toyota Landcruiser. This console was also offered in years after 1984 in some markets. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has two different sized holes to accept all types of cups. This can hold the usual fastfood cup, coffee cups with handles, and even the large yeti 40oz cups with ease. The cup holder also has a slot for an LED flashlight, a slot for a knife/multi tool, and two pend slots. Along the one side there is room to hold two cell phones as well. This will come with 2 strips of 3M automotive adhesive on bottom in case you want to permanently attach it to the console but that is not required for install. No hardware or tools are needed for install.
1973-1978 40 Series Double Cup Holder
This is a double cup holder insert for the stamped metal center console of a 1973-1978 Toyota Landcruiser. This is made of ABS plastic with a 3d printer. It will come with a smooth flat black finish. This cup holder has holes at 3.25″ diameter to accept large fast food cup type drinks and the 30/40 oz yeti type thermos. It will also hold smaller containers securely. This insert also has two slots for pens, a slot for a knife/multi-tool, a slot for an LED flashlight and still leave a 1.2″ slot in the rear for a cell phone or wallet. It will allow that awkward hole to have good functional use of the space. There will be 2 strips of 3M automotive adhesive on the bottom in case you want to permanently secure it to the bottom of the console. This is not needed for install. No hardware needed.
70 Series Cup Holder-Go to Odd Iron Offroad For Purchasing-Link Below
Now sold at our vendor site at http://www.oddironoffroad.com/store#!/70-Series-Cup-Holders-by-BH3D/p/82522362/category=23176020
This is a double cup holder for the 70 series landcruiser. This cup holder has a slot for 2 drinks, 2 pens, a cell phone, and a slot for a multi-tool or knife. It comes in a flat black finish. There are two versions. Both designs will work on either the RHD or LHD variants. Both have the some shape/functions up top but mount very differently. One cup holder is for the 70 series that came with a center console that goes up and around the shifters. It will mount up on top of the consoles and will come with 6 strips of 3M adhesive to secure it. It also has screw holes that will line up with the factory screw holes if you want to screw it down. You will need to source the screw. This cup holder can be flipped 180 degrees to go on either the RHD or LHD. The other double cup holder mounts to the floor of the 70 series landcruiser. It will also come with strips of 3M adhesive. That alone with not be adequate for attachment. You will need to screw the floor mounted cup holder into the floor. 2 self taping screws will be provided for that model. There are two countersunk holes at the bottom of this cup holder to guide you in placement of the screws. These cup holders are 3D printed and made of ABS plastic. I can do certain custom colors upon request. I have color matches in brown and gray for certain years/models 70 series but not all.