Show sidebar

80 Series/LX450 Double Cup Holder

$6.00$60.00

This is a double cup holder for a 91-97 Toyota LandCruiser and 96-97 Lexus LX450. It also has a cell phone holder, 2 pen holders, and a flash light holder. This comes in the factory Tan “Oak” color common to the LX450 and some Toyota LandCruisers and the Toyota Gray that is common on LandCruisers. I also offer this is the Right Hand Drive (RHD) version for the non US spec console. The black inserts are removeable to allow for larger beverage containers like a nalgene bottle. I also have an optional “small insert” that fits into the existing inserts that will allow better fitment of more narrow and tall beverage containers like insulated travle mugs, soda cans, and grocery store water bottles. This item comes with 3m automotive adhesive installed on the bottom side. You can use the adhesive strips only to mount this but I would encourage you to also use the 4 provided screws/holes for added insurance. You need to predrill the holes on the center console with a smaller bit then the diameter of the screw. If you don’t predrill the holes you risk cracking the plastic on the center console. DON’T use a powered drill to screw in the screws. You can easily over torque the screws and strip the plastic holes. Use a handheld screwdriver and stop when you get decent resistance. If you have any questions feel free to message me on here. I will get back to you within 24 hours.

Additional Small Insert
Gray
Gray RHD-Non US Spec
Gray with small insert
Tan "Oak"
Tan RHD-Non US Spec
Tan with small insert

80 Series Cup Holder Console Insert

$32.00

This is a single cup holder that fits snugly into the square hole at the front of most 80 series LandCruisers. The LX450 came with a sub woofer in this hole so this cup holder will only fit in the 91-97 Toyota Landcruiser and not LX450. It has a slot for a cell phone that is the width of the square hole. If your phone fits in the square hole now it will fit with the cup holder installed. The cup holder diameter at the top is 3″ with a slight taper towards the bottom. If you need something larger than 3″ then you will want to buy the single or double cup holder set up that mounts on the side of the shifter console. There are also two pen holders that are tilted forward by 15 degrees to make sure the pens don’t interfere with any cup. Soda cans, water bottles, and all fast food cups all fit without issue. Anything bigger (like a Nalgene bottle) will not. These come in the factory Oak tan color and the dark gray color. These are made of ABS plastic through my 3D printer. Install is simple. Remove the 3M adhesive backing and push it into the hole until it hits bottom. It’s a snug fit so it will take a little force to get it to seat all the way into the bottom. I wanted it to be a snug fit so that if a large cup is put into it with a snug fit, it wont pull the entire insert out when you remove the cup. No screws are needed but I left the factory hole at the bottom available if you decided to run a longer screws and anchor it into place.

80 Series/LX450 Rear Double Cup Holder

$6.00$60.00

This is a rear double cup holder for the 91-97 Toyota Land Cruiser and Lexus LX450. It has a storage slot underneath that can hold sunglasses or anything else in that size range. The small circle in the front between the cup slots is for an LED flashlight (not provided). The normal hardware store/harbor freight small LED flashlight will fit in that slot. Most stores carry that size. The black inserts are removable and allow for a wide range of different types of containers. There is also an optional “Travel Mug” insert. This allows for better fitment of tall containers with a narrow bottom. You can add 1 or 2 of these to the order. The rear double cup holder comes in the factory “Oak” tan color and the dark gray. There are 2 types of attachment. The first is the the 3 large strips of 3M automotive adhesive on the backside and 2nd are 4 screw holes and provided self tapping screws.  Make sure to use both forms of attachment.  In regards to installation, make sure you clean the backside of the console.  Simply stick the cup holder on the back of the console in your desired location. Then add the four screws with a screwdriver. Don’t use a power drill or you may strip the holes.

Additional Small Insert
Gray
Gray with small insert
Tan
Tan with small insert

200 Series Double Cup Holder

$75.00$80.00

This is a complete drop in cup holder replacement. The OEM cup holder and lid needs to be removed completely for this to be inserted. This is made in ABS plastic with a flat textured black finish. There are 2 versions for the Cruiser and LX570. Version 1 has one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. Version 2 has two large holes with 2 removable snap rings. This option can hold 2 of the large containers like a 32/40oz. Hydroflask, Yeti bottles, and Nalgene bottle but can not hold a cell phone due to space issues. There are strips of 3M adhesive on the bottom of the new cup holder but is not necessary for install. The cup holder is stable without the adhesive but provided in case the installer wants something extremely secure. To remove the OEM cup holder just open the lid and pull upward with about 10lbs of force. The OEM cup holder simply snaps into the hole with no use of hardware or adhesive. You may want to tap the cup holder with the handle of a screw driver as you pull to help dislodge. 

Cruiser 08-15 Design #1
Cruiser 08-15 Design #2
Cruiser 16-22 Design #1
Cruiser 16-22 Design #2
LX570 08-15 Design #1
LX570 08-15 Design #2

200 Series/LX570 Cup Holder Inserts

$48.00

This is a 3D printed cup holder insert that goes inside of the OEM recessed cup holder hole of the 200 Series Landcrusier and the Lexus LX570. These are 3″ diameter holes allowing for a much more secure smaller hole than the OEM holes. This will fit most beverage containers out there but not all. If drinking from something large you can simply remove the insert for a larger hole. This is made of ABS plastic. There are 3 options. Option one is for the Landcruiser Console. This option allows for the lid to close. Option 2 is for the LX570 console. This option does NOT allow the lid to close. It is the same depth as the Landcruiser insert but since the LX570 console is more shallow, you can’t close the lid. Option 3 is is also for the LX570 console but it DOES allow the lid to close. This option follows the curvature of the lid so it can close but it is more shallow. No screws, adhesive, or hardware of any kind is used. Simply insert and your done.

Aluminum TEQ Universal Badge (Round and Oval)

$29.00$35.00

These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.

Oval Bare Aluminum
Oval Black/Silver
Oval Red/Silver
Round Bare Aluminum
Round Black/Silver
Round Red/Silver

80/100/LX450/LX470 TEQ grill badge

$40.00

This machined aluminum TEQ badge mounts onto the front grille of your a 91-94 & 95-97 Toyota LandCruiser (80 series) and the 98-07 (100 series). WIll also mount to the LX450 and LX470 Lexus. I offer the badge in the retro red/silver, the black/silver, and bare aluminum for the folks who want to do there own paint color. The factory chrome “sombrero” must be removed. For the 95-02 Cruiser and LX TEQ badge the easiest way to install the emblem is to remove the entire grill and then install the emblem. This is not a must. You can use a stubby screwdriver and pliers, but you will need some patience and a cool car; NOT a hot radiator. Don’t forget to remove the backing from the 3M adhesive. You want to run the screws through the backside of the grill first. Make SURE to use the provided black washers between the screws and backside of the grill. They are for spacing purposes to get the TEQ badge perfectly flat to your grill. Once the screws are through then start each screw with a full turn but prevent the adhesive from grabbing the grill Do not tighten the screws until all of them have been started. That will ensure you get everything lined up properly. Once the screws have threaded in slightly then you can press the badge onto the grill and the adhesive will hold it nice and snug while you screw in the 3 screws. Between the adhesive and screws everything should stay nice and flush. Reinstall the grille in the same way you removed it. IF you are buying the 03-07 badge then there were no screws used on the OEM sombrero badge. Toyota only used adhesive. You will need to pry the factory badge off. Some heat and fishing line will help. There are small tabs that help center the badge so you will not be able to simply run the fishing line all the way down the back side. Once the badge and adhesive are removed, you will simply stick the new badge on using the same type of 3M adhesive. No hardware needed for the 03-07 badge and no need to remove the grill.

80 Series/LX450 Single Cup Holder

$6.00$42.00

This is a single cup holder with cell phone holder and a pen holder for a 91-97 Toyota LandCruiser and Lexus LX450. There are two color options. There is a factory tan color which is the “Oak” common to the LX and some Toyotas. There is also the factory dark gray color common to most LandCruisers. the black insert is removeable to allow for larger beverage containers like a nalgene bottle. There is also an optional “travel mug” insert to allow tight/stable fitment on narrow and tall beverage containers. The cupholder comes with strips of 3m automotive adhesive already installed. You need to peel off the red cover. You can install the cupholder with zero screws and only use the adhesive, but I would advise you to use the screw holes AND adhesive to guarantee the cupholder never moves on you. Screws are provided. Please pre-drill the hole with a bit smaller than the screw so you don’t risk cracking the plastic on the center console. Make sure you place in the spot you like the most because once you stick it down the adhesive doesn’t want to let go. There is about 3″ of adjustability in and out to your desired location on the center console. For any questions just send me a message on here and I will get back to you within 24 hours. 

Gray RHD with small insert
Tan "Oak" RHD
Tan "Oak" RHD with small insert
Tan "Oak" with small insert
Gray
Gray RHD
Gray with small insert
Single Small Insert
Tan "Oak"

80 Series (95-97) Dash Bezel/Cell Phone Mount

$6.00$52.00

This is an accessories dash bezel for the 80 series (95-97) dash. There is only one type of bezel that accepts all the different options. This will also fit the LX450. This is made of ABS plastic and will allow you to add two more accessories like OEM and Aftermarket buttons/switches, CB mic holder, cell phone holder, single 1″ RAM ball, and a double 1″ RAM ball. If the dash came with the factory pull out single cup holder then that will need to be removed. If there is a black plastic hollow insert/cubby instead of the pull out cup holder then the insert will need to be removed and discarded. The holding tabs for the factory insert are at the top. You need to compress them to pull out the insert from the dash. Reuse the two factory screws in the dash that are behind the cover to install the bezel. The cell phone holder will come with an additional 4 screws for mounting. You can also add a plug or two if you do not have two accessory buttons yet. There is also a CB mic holder that can be placed in one of the holes. The cell phone mount, plugs/inserts, RAM Ball, and CB holder are an extra cost. The finish of the bezel and inserts are a satin black to match the other black parts on the dash.

60 Series Double Cup Holder

$45.00

This is a double cup holder insert for the 60 Series Toyota Landcruiser. This cup holder is made of ABS plastic. It comes in a black satin finish. It will hold 2 cups, a cell phone, and 2 pens. There are strips of 3M adhesive installed on the bottom to stick it down into the hole. There are also 2 self taping screws provided. You can use the adhesive only or the adhesive and screws; depending on how secure you feel you need it.

62 Series Single Cup Holder Square Insert

$32.00

This is a single cup holder for the 62 Series Toyota Landcruiser. It will fit snugly into the square hole near the front of the center console. It has a spot for a cup, a cell phone, 2 pens, and a storage slot in the rear. It has a black satin finish and is made of ABS plastic. It comes with 2 strips of 3M automotive adhesive on the bottom to bond it into the hole if desired. No screws or drilling of any kind needed.