Showing all 5 results
This is a single cup holder for the 62 Series Toyota Landcruiser. It will fit snugly into the square hole near the front of the center console. It has a spot for a cup, a cell phone, 2 pens, and a storage slot in the rear. It has a black satin finish and is made of ABS plastic. It comes with 2 strips of 3M automotive adhesive on the bottom to bond it into the hole if desired. No screws or drilling of any kind needed.
This is a double cup holder insert for the 62 Series Toyota Landcruiser. This cup holder will hold two cups, two phones, a wallet, a pen/pencil, and a flashlight. It is designed to fit the transmission hump in front of the center console. It will lay flat on the hump and match the contours of the 60 series interior. This is made of ABS plastic with a black satin finish. It will come with strips of 3M adhesive installed and 4 self taping screws. You can use the adhesive only or the adhesive and screws; depending on how secure you want the cup holder.
This is a cup holder for the 1st gen body 4runner. It is for the manual transmission set up ONLY. It will hold just about any fast food cup size drink with the insert installed. With the insert removed it can hold a large sports (Nalgene) bottle. There is also a pen holder and cell phone holder. The inside width of the cell phone slot is 3.25″ That should accept just about any cell phone on the market including the new IPhone6 plus. There are two avialable colors: the dark gray or black. Both colors come in a satin/flat finish. Installation: There are two strips of 3M automotive adhesive underneath the cup holder to aid in attachment. There are also 2 screw holes located at the bottom of the cell phone tray and on the bottom outer edge. Two self taping screws are provided. No drill bits or power tools are needed. Just thread the screws into the plastic with a handheld phillips screw driver. They will drill themselves into the plastic. Do NOT over tighten. You are threading into thin plastic. Thread the screws in until they are snug and stop.
This is a single cup holder for the 84-89 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot that is 3.5″ wide which will accept just about every major phone style available. There is a notch at the bottom of the cell phone slot to allow a charging cable to be ran up from the bottom. Be aware you will need to cut a hole in the bottom on the console to be able to run the cable. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There is a countersunk hole at the bottom in case you want to screw it in. That is not a must, just a preference. Any 3/4″- 1″ coarse thread screw will work. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only. Be aware that there are 4 different consoles that came on the 1st gen 4Runner and this insert will only fit in two of them(which do seem to be the more popular options). Make sure to look at the pics to make sure they match your console.
This is a double cup holder for the 1st gen 4Runner. Be aware that there are two very different options. One option is for the folks with the short center console with the larger storage tray. This is NOT for the short console with rear heat. This option is only for the non heat short console. It comes with a cell phone slot, 2 pen holders, and a multi-tool/knife holder. Option two is for the later model gen 1’s with the taller console with padded armrest. This storage tray is more narrow. This option does not have the cell phone slot or knife holder due to lack of space. It does still hold two pens. These are made of ABS plastic. They will come in an unpainted gloss black finish. The gloss finish is for durability and ease of cleaning. It can be painted any color if desired.