80 Series/LX450 Double Cup Holder
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
80 Series/LX450 Single Cup Holder
80 Series (95-97) Dash Bezel/Cell Phone Mount
This is an accessories dash bezel for the 80 series (95-97) dash. There is only one type of bezel that accepts all the different options. This will also fit the LX450. This is made of ABS plastic and will allow you to add two more accessories like OEM and Aftermarket buttons/switches, CB mic holder, cell phone holder, single 1″ RAM ball, and a double 1″ RAM ball. If the dash came with the factory pull out single cup holder then that will need to be removed. If there is a black plastic hollow insert/cubby instead of the pull out cup holder then the insert will need to be removed and discarded. The holding tabs for the factory insert are at the top. You need to compress them to pull out the insert from the dash. Reuse the two factory screws in the dash that are behind the cover to install the bezel. The cell phone holder will come with an additional 4 screws for mounting. You can also add a plug or two if you do not have two accessory buttons yet. There is also a CB mic holder that can be placed in one of the holes. The cell phone mount, plugs/inserts, RAM Ball, and CB holder are an extra cost. The finish of the bezel and inserts are a satin black to match the other black parts on the dash.
80/100/LX450/LX470 Rear TEQ Badge (91-07)
This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).
(91-94) 80 Series Dash Phone Mount
This is a dash mounted cell phone mount for the 91-94 80 Series Landcruiser. At full width it’s just over 4″ wide. The lower mount is 3D printed out of ABS plastic. It is held on with 2 strips of 3M automotive adhesive and 4 self taping 1/2″ screws. You can use a power drill to drill/thread the screws in BUT use a hand screwdriver to tighten them down the last little bit. Tightening down the screws with a power drill may crack the dash or strip the hole.
80 Series 3rd Row Cup Holders
This is a double cup holder for the 3rd row of the 1993-1997 Toyota Landcruiser. It does NOT fit the 91-92 Landcruiser due to it not having arms rests for the middle row. This cup holders hangs on the back of the 2nd row. There is no hardware or adhesive used. It does not effect the function of the middle row armrests or their movement. It can hang on either middle row seat allowing on of the middle row seats to be folded down without issue if desired. It is a very snug fit and will take some wiggling to slide it all the way down onto the middle row seat. It is designed this way to keep heavy drinks secure and prevent bouncing around. These are made of ABS plastic through the use of a 3D printer. They come in the factory tan and gray as well as a satin black. The cupholder can easily be removed at any time.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.