80 Series/LX450 Double Cup Holder
This is a double cup holder for a 91-97 Toyota LandCruiser and 96-97 Lexus LX450. It also has a cell phone holder, 2 pen holders, and a flash light holder. This comes in the factory Tan “Oak” color common to the LX450 and some Toyota LandCruisers and the Toyota Gray that is common on LandCruisers. I also offer this is the Right Hand Drive (RHD) version for the non US spec console. The black inserts are removeable to allow for larger beverage containers like a nalgene bottle. I also have an optional “small insert” that fits into the existing inserts that will allow better fitment of more narrow and tall beverage containers like insulated travle mugs, soda cans, and grocery store water bottles. This item comes with 3m automotive adhesive installed on the bottom side. You can use the adhesive strips only to mount this but I would encourage you to also use the 4 provided screws/holes for added insurance. You need to predrill the holes on the center console with a smaller bit then the diameter of the screw. If you don’t predrill the holes you risk cracking the plastic on the center console. DON’T use a powered drill to screw in the screws. You can easily over torque the screws and strip the plastic holes. Use a handheld screwdriver and stop when you get decent resistance. If you have any questions feel free to message me on here. I will get back to you within 24 hours.
80 Series Cup Holder Console Insert
This is a single cup holder that fits snugly into the square hole at the front of most 80 series LandCruisers. The LX450 came with a sub woofer in this hole so this cup holder will only fit in the 91-97 Toyota Landcruiser and not LX450. It has a slot for a cell phone that is the width of the square hole. If your phone fits in the square hole now it will fit with the cup holder installed. The cup holder diameter at the top is 3″ with a slight taper towards the bottom. If you need something larger than 3″ then you will want to buy the single or double cup holder set up that mounts on the side of the shifter console. There are also two pen holders that are tilted forward by 15 degrees to make sure the pens don’t interfere with any cup. Soda cans, water bottles, and all fast food cups all fit without issue. Anything bigger (like a Nalgene bottle) will not. These come in the factory Oak tan color and the dark gray color. These are made of ABS plastic through my 3D printer. Install is simple. Remove the 3M adhesive backing and push it into the hole until it hits bottom. It’s a snug fit so it will take a little force to get it to seat all the way into the bottom. I wanted it to be a snug fit so that if a large cup is put into it with a snug fit, it wont pull the entire insert out when you remove the cup. No screws are needed but I left the factory hole at the bottom available if you decided to run a longer screws and anchor it into place.
80 Series/LX450 Rear Double Cup Holder
This is a rear double cup holder for the 91-97 Toyota Land Cruiser and Lexus LX450. It has a storage slot underneath that can hold sunglasses or anything else in that size range. The small circle in the front between the cup slots is for an LED flashlight (not provided). The normal hardware store/harbor freight small LED flashlight will fit in that slot. Most stores carry that size. The black inserts are removable and allow for a wide range of different types of containers. There is also an optional “Travel Mug” insert. This allows for better fitment of tall containers with a narrow bottom. You can add 1 or 2 of these to the order. The rear double cup holder comes in the factory “Oak” tan color and the dark gray. There are 2 types of attachment. The first is the the 3 large strips of 3M automotive adhesive on the backside and 2nd are 4 screw holes and provided self tapping screws. Make sure to use both forms of attachment. In regards to installation, make sure you clean the backside of the console. Simply stick the cup holder on the back of the console in your desired location. Then add the four screws with a screwdriver. Don’t use a power drill or you may strip the holes.
80 Series/LX450 Single Cup Holder
This is a single cup holder with cell phone holder and a pen holder for a 91-97 Toyota LandCruiser and Lexus LX450. There are two color options. There is a factory tan color which is the “Oak” common to the LX and some Toyotas. There is also the factory dark gray color common to most LandCruisers. the black insert is removeable to allow for larger beverage containers like a nalgene bottle. There is also an optional “travel mug” insert to allow tight/stable fitment on narrow and tall beverage containers. The cupholder comes with strips of 3m automotive adhesive already installed. You need to peel off the red cover. You can install the cupholder with zero screws and only use the adhesive, but I would advise you to use the screw holes AND adhesive to guarantee the cupholder never moves on you. Screws are provided. Please pre-drill the hole with a bit smaller than the screw so you don’t risk cracking the plastic on the center console. Make sure you place in the spot you like the most because once you stick it down the adhesive doesn’t want to let go. There is about 3″ of adjustability in and out to your desired location on the center console. For any questions just send me a message on here and I will get back to you within 24 hours.
3rd Gen 4Runner Single CupHolder 96-02
This is a single cup holder for the 3rd gen Toyota 4Runner. It is made of ABS plastic and comes in the two factory colors which are tan “Oak” and the dark gray. The cup holder will hold any fast food cup and most beverage container sizes. If you remove the black insert then you have a much larger diameter cup holder for items like a Nalgene bottle. The cell phone slot 3.25″ across and .65″ deep which will allow for most larger cell phones on the market with a case. There is also a pen holder. This single cup holder DOES allow for almost full movement of the passenger seat front to back. You lose about 1/2″ of forward movement which is very minimal. You could push the cup holder forward to allow for full movement of the seat but that would cause the larger fast food cups to come in contact with the dash but that is also minimal. This is available for the automatic and now manual trans. Install Instructions There are 3 strips of 3m automotive adhesive already installed. This is the primary method of attachment. Make SURE the console is cleaned really well before you attach and use good force when attaching. The cup holder will not bond well if the console is not clean. 2 screws are also included to be used in the 2 screw holes. The screws are an added insurance to ensure the cup holder is secure. I would highly encourage you to use the screws. Use a small drill bit and predrill the holes once the cup holder has been stuck into place. Then use a hand held screw driver to thread the screws in. Do not use a drill because you will probably strip the screw hole. Also, do not over tighten them by hand. Turn the screw until it is snug and then stop.
62 Series Single Cup Holder Square Insert
This is a single cup holder for the 62 Series Toyota Landcruiser. It will fit snugly into the square hole near the front of the center console. It has a spot for a cup, a cell phone, 2 pens, and a storage slot in the rear. It has a black satin finish and is made of ABS plastic. It comes with 2 strips of 3M automotive adhesive on the bottom to bond it into the hole if desired. No screws or drilling of any kind needed.
1995-2004 Tacoma Single Cup holder
This is a single cup holder for the 1996-2004 Toyota Tacoma. There are two versions. One is for the 2WD/4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder allows for full movement of the passenger seat into the forward position. This cup holder will hold one drink, a flashlight, and 1 pen. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
Cup Holder Ashtray Insert 40 Series 81-84
This is a cup holder that inserts into the ashtray slot on the 1981-1984 Toyota Landcruiser 40 Series. This mounts to the center console and you must have the center console for this to work. It has a 3.25″ top diameter which will accept a majority of drink containers on the market. It also has a small storage cubby at the bottom for loose change or whatever else you want to store in there. This is made of ABS plastic with a satin black finish.
1995-2004 Tacoma Single Cup holder
This is a single cup holder for the 1996-2004 Toyota Tacoma. There are two versions. One is for the 2WD/4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder allows for full movement of the passenger seat into the forward position. This cup holder will hold one drink, a flashlight, and 1 pen. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.