Show sidebar

Universal 2oz. Hand Sanitizer Holder

$10.00$15.00

This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.

Select options This product has multiple variants. The options may be chosen on the product page

BH3D T-Shirt

$13.00

These t-shirts are made of a very soft durable cotton from Next Level Apparel. They come in a gun metal gray color. It tends to run as a slight “slim” fit meaning it’s a little bit more snug in the shoulders and arms. They are a good long length for men but run a little snug. If you like a loose fitting shirt then I would say order one size up from what you normally where.

Select options This product has multiple variants. The options may be chosen on the product page
Medium
Small

BH3D Hat (Free with purchase over $100)

$15.00

This is a BH3D adjustable fit mesh back hat. It’s a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.

Aluminum TEQ Universal Badge (Round and Oval)

$29.00$35.00

These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.

Select options This product has multiple variants. The options may be chosen on the product page
Oval Bare Aluminum
Oval Black/Silver
Oval Red/Silver
Round Bare Aluminum
Round Black/Silver
Round Red/Silver

Universal Turbo Badge

$30.00$40.00

This is an aluminum retro “Turbo” badge. This is inspired by the “Turbo” badge Toyota made in the 1980s. It can mount to any flat surface on the vehicle. Will come with 1-2 strips (depending on size) of 3M automotive adhesive to mount to the vehicle. There are 2 sizes and two color options for each size for a total of 4 options. There is the 7″ and 5″ black/silver badges. There is also the 7″ and 5″ black/silver/red badges.

Select options This product has multiple variants. The options may be chosen on the product page
5" Black
5" Red/Black
7" Black
7" Red/Black

80/100/LX450/LX470 Rear TEQ Badge (91-07)

$36.00$40.00

This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).

Select options This product has multiple variants. The options may be chosen on the product page
100 Series Bare Metal
100 Series Black/Silver
100 Series Red/Silver
80 Series Bare Metal
80 Series Black/Silver
80 Series Red/Silver

80/100/LX450/LX470 TEQ grill badge

$40.00
Select options This product has multiple variants. The options may be chosen on the product page

Universal Diesel/TEQ badge

$38.00

This is a Universal Aluminum TEQ/Diesel badge for a Toyota. The lettering is inspired by the Diesel font used by Toyota throughout the early 80s to late 90s. This is designed to mount on any flat smooth surface on the vehicle. It comes with strips of 3M automotive adhesive on back for attachment.

1979-1983 Toyota Pickup Fender Badge (Universal Fit)

$40.00

This is a machined aluminum badge with a satin brushed finish on the lettering. This is not a plastic replica like the OEM badge was. This badge is an exact match in size to the original factory badge and mounts with strips of 3M automotive badge/decal adhesive. No drilling of the fenders is needed. The overall length is exactly 10″  (254mm) by 1.4″(36mm) tall. This badge will fit in the factory fender location of the 1979-1983 Toyota pickup BUT it can also mount to any flat surface of any Toyota. It can be mounted on a surface like a flat tailgate of a more modern vehicle giving it that old school retro look.