This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.
This is a brushed aluminum TEQ badge that can be mounted on all years FJ Cruisers and can be mounted in numerous locations on the upper and lower grille. The backing plate is installed from the rear of the grille. Provided strips of 3m automotive adhesive are already installed on the back of the emblem. You simply need to remove the red backing from the tape and stick the emblem onto the backing plate. Use good force when installing the adhesive. The install should take 1-2 minutes tops. No tools are needed. This adhesive is VERY sticky so make sure you line it up and get it straight before you stick it on. You probably want someone to hold the backing plate in place while you install the TEQ badge so you can be directly in front and level with the badge as you install it to guarantee you get it straight. I have the black/silver, red/silver, and bare aluminum in stock. The bare aluminum would be for the folks looking to color match their paint.
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.