Showing all 7 results
This is a double cup holder for a 91-97 Toyota LandCruiser and 96-97 Lexus LX450. It also has a cell phone holder, 2 pen holders, and a flash light holder. This comes in the factory Tan “Oak” color common to the LX450 and some Toyota LandCruisers and the Toyota Gray that is common on LandCruisers. I also offer this is the Right Hand Drive (RHD) version for the non US spec console. The black inserts are removeable to allow for larger beverage containers like a nalgene bottle. I also have an optional “small insert” that fits into the existing inserts that will allow better fitment of more narrow and tall beverage containers like insulated travle mugs, soda cans, and grocery store water bottles. This item comes with 3m automotive adhesive installed on the bottom side. You can use the adhesive strips only to mount this but I would encourage you to also use the 4 provided screws/holes for added insurance. You need to predrill the holes on the center console with a smaller bit then the diameter of the screw. If you don’t predrill the holes you risk cracking the plastic on the center console. DON’T use a powered drill to screw in the screws. You can easily over torque the screws and strip the plastic holes. Use a handheld screwdriver and stop when you get decent resistance. If you have any questions feel free to message me on here. I will get back to you within 24 hours.
80 Series/LX450 Double Cup Holder
$6.00 – $60.00
This is a single cup holder that fits snugly into the square hole at the front of most 80 series LandCruisers. The LX450 came with a sub woofer in this hole so this cup holder will only fit in the 91-97 Toyota Landcruiser and not LX450. It has a slot for a cell phone that is the width of the square hole. If your phone fits in the square hole now it will fit with the cup holder installed. The cup holder diameter at the top is 3″ with a slight taper towards the bottom. If you need something larger than 3″ then you will want to buy the single or double cup holder set up that mounts on the side of the shifter console. There are also two pen holders that are tilted forward by 15 degrees to make sure the pens don’t interfere with any cup. Soda cans, water bottles, and all fast food cups all fit without issue. Anything bigger (like a Nalgene bottle) will not. These come in the factory Oak tan color and the dark gray color. These are made of ABS plastic through my 3D printer. Install is simple. Remove the 3M adhesive backing and push it into the hole until it hits bottom. It’s a snug fit so it will take a little force to get it to seat all the way into the bottom. I wanted it to be a snug fit so that if a large cup is put into it with a snug fit, it wont pull the entire insert out when you remove the cup. No screws are needed but I left the factory hole at the bottom available if you decided to run a longer screws and anchor it into place.
80 Series Cup Holder Console Insert
$32.00
This is a rear double cup holder for the 91-97 Toyota Land Cruiser and Lexus LX450. It has a storage slot underneath that can hold sunglasses or anything else in that size range. The small circle in the front between the cup slots is for an LED flashlight (not provided). The normal hardware store/harbor freight small LED flashlight will fit in that slot. Most stores carry that size. The black inserts are removable and allow for a wide range of different types of containers. There is also an optional “Travel Mug” insert. This allows for better fitment of tall containers with a narrow bottom. You can add 1 or 2 of these to the order. The rear double cup holder comes in the factory “Oak” tan color and the dark gray. There are 2 types of attachment. The first is the the 3 large strips of 3M automotive adhesive on the backside and 2nd are 4 screw holes and provided self tapping screws. Make sure to use both forms of attachment. In regards to installation, make sure you clean the backside of the console. Simply stick the cup holder on the back of the console in your desired location. Then add the four screws with a screwdriver. Don’t use a power drill or you may strip the holes.
80 Series/LX450 Rear Double Cup Holder
$6.00 – $60.00
This is a single cup holder with cell phone holder and a pen holder for a 91-97 Toyota LandCruiser and Lexus LX450. There are two color options. There is a factory tan color which is the “Oak” common to the LX and some Toyotas. There is also the factory dark gray color common to most LandCruisers. the black insert is removeable to allow for larger beverage containers like a nalgene bottle. There is also an optional “travel mug” insert to allow tight/stable fitment on narrow and tall beverage containers. The cupholder comes with strips of 3m automotive adhesive already installed. You need to peel off the red cover. You can install the cupholder with zero screws and only use the adhesive, but I would advise you to use the screw holes AND adhesive to guarantee the cupholder never moves on you. Screws are provided. Please pre-drill the hole with a bit smaller than the screw so you don’t risk cracking the plastic on the center console. Make sure you place in the spot you like the most because once you stick it down the adhesive doesn’t want to let go. There is about 3″ of adjustability in and out to your desired location on the center console. For any questions just send me a message on here and I will get back to you within 24 hours.
80 Series/LX450 Single Cup Holder
$6.00 – $42.00
This is an accessories dash bezel for the 80 series (95-97) dash. This will also fit the LX450. This is made of ABS plastic and will allow you to add two more accessories like OEM and Aftermarket buttons/switches, CB mic holder, and a cell phone holder. If the dash came with the factory pull out single cup holder then that will need to be removed. If there is a black plastic hollow insert/cubby instead of the pull out cup holder then the insert will need to be removed and discarded. The holding tabs for the factory insert are at the top. You need to compress them to pull out the insert from the dash. Reuse the two factory screws to install the bezel. The cell phone holder will come with an additional 4 screws for mounting. You can also add a plug or two if you do not have two accessory buttons yet. There is also a CB mic holder that can be placed in one of the holes. The cell phone mount, plugs/inserts, and CB holder are an extra cost. The finish of the bezel and inserts is a satin black to match the other black parts on the dash.
95-97 Accessories Dash Bezel/Cell Phone Mount 80 Series
$6.00 – $45.00
This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).
80/100/LX450/LX470 Rear TEQ Badge (91-07)
$36.00 – $40.00
This is a double cup holder for the 1990-1995 Toyota 4Runner. It is made of ABS plastic. It will hold two cups, 2 cell phones, 2 pens, and a flashlight. The black insert gives you a 3″ diameter hole to hold a large variety of drinks. The smaller hole(closer to driver) is about 2 3/4″ which holds soda cans, water bottles, and medium sized drinks nice and snug. With the black insert removed you have a 3 3/4″ hole which holds a Nalgene sports bottle and other large bottles. This comes in the factory Tan, gray, golden brown, and satin black. This attaches with 2-4 self taping screws and strips of 3M automotive adhesive. The amount of screws varies between the 2WD, 4WD, and manual tranny cup holders due to the curvatures of each console and the screws needed to make it secure.