Aluminum Tacoma Grille Badge 2001-2004
This is a 2 piece aluminum TEQ grille badge for the 2001-2004 Toyota Tacoma. The outer visible piece is made from machined aluminum. The backing plate that goes behind the grille and protrudes forward to the front is made of 3D printed ABS plastic. Look at the pictures to fully understand the 2 piece design. This comes in two options; there is the satin black and gloss red finish. You can also order in bare aluminum and add your own color option. There are no tools needed and no hardware used. The factory badge must be removed first and then the backing plate will slide in behind the grille opening. You do not need to remove the grille to do this. Just pop the hood for easy access. The TEQ badge will have 3M adhesive on the backside. Remove the red backing tape from the adhesive and simply stick the badge onto the backing plate sandwiching the grille in between. Use good force while clamping and hold there for 20 seconds to ensure a good bond.
3rd Gen 4Runner (96-02) Rear Hatch TEQ Badge
This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.
80 Series 3rd Row Cup Holders
This is a double cup holder for the 3rd row of the 1993-1997 Toyota Landcruiser. It does NOT fit the 91-92 Landcruiser due to it not having arms rests for the middle row. This cup holders hangs on the back of the 2nd row. There is no hardware or adhesive used. It does not effect the function of the middle row armrests or their movement. It can hang on either middle row seat allowing on of the middle row seats to be folded down without issue if desired. It is a very snug fit and will take some wiggling to slide it all the way down onto the middle row seat. It is designed this way to keep heavy drinks secure and prevent bouncing around. These are made of ABS plastic through the use of a 3D printer. They come in the factory tan and gray as well as a satin black. The cupholder can easily be removed at any time.
1981-1984+ 40 Series Double Cup Holder
This is a double cup holder for a 1981-1984+ FJ40 Toyota Landcruiser. This console was also offered in years after 1984 in some markets. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has two different sized holes to accept all types of cups. This can hold the usual fastfood cup, coffee cups with handles, and even the large yeti 40oz cups with ease. The cup holder also has a slot for an LED flashlight, a slot for a knife/multi tool, and two pend slots. Along the one side there is room to hold two cell phones as well. This will come with 2 strips of 3M automotive adhesive on bottom in case you want to permanently attach it to the console but that is not required for install. No hardware or tools are needed for install.
1995-2004 Tacoma Single Cup holder
This is a single cup holder for the 1996-2004 Toyota Tacoma. There are two versions. One is for the 2WD/4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder allows for full movement of the passenger seat into the forward position. This cup holder will hold one drink, a flashlight, and 1 pen. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
BH3D Hat (Free with purchase over $100)
This is a BH3D adjustable fit mesh back hat. It’s a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.
1995-2004 Tacoma Double Cup Holder
This is a double cup holder for the 1995-2004 Toyota Tacoma. There are two versions. One is for the 2WD and 4WD automatic and one is for the 2WD/4WD manual tranny. They are identical other than the mounting surfaces underneath. They come in the two factory colors of gray or tan. You can also order in satin black if preferred. It is made of ABS plastic. This cup holder will hold two drinks, a cell phone, flashlight, and 2 pens. It mounts with 2 strips of 3M automotive adhesive and 2 self taping screws. The screws are not a must for install but are a nice added bit of insurance for extra strength if you are adding two large drinks. The cup holder will hook up onto the console by wedging itself between the tranny shifter bezel and the console bezel. If you have the automatic tranny version you may need to wiggle the console and shifter bezel a bit to get the hook to slide down into place. It is a snug fit but does fit.
1973-1978 40 Series Double Cup Holder
This is a double cup holder insert for the stamped metal center console of a 1973-1978 Toyota Landcruiser. This is made of ABS plastic with a 3d printer. It will come with a smooth flat black finish. This cup holder has holes at 3.25″ diameter to accept large fast food cup type drinks and the 30/40 oz yeti type thermos. It will also hold smaller containers securely. This insert also has two slots for pens, a slot for a knife/multi-tool, a slot for an LED flashlight and still leave a 1.2″ slot in the rear for a cell phone or wallet. It will allow that awkward hole to have good functional use of the space. There will be 2 strips of 3M automotive adhesive on the bottom in case you want to permanently secure it to the bottom of the console. This is not needed for install. No hardware needed.
70 Series Steering Column Insert (pair)
- This is a pair of 3D printed rubber inserts for the steering column of the 70 Series Toyota Landcruiser. This is designed to fill the open hole on the side of the steering column. This does NOT make the steering column waterproof. It is simply to visually give the column a finished look. This design does not require any tools or disassembly of any components. Just slide the boot over the end of the blinker/wiper column and snap it into the hole. This is a very snug fit so you will need to wiggle it into place a bit to properly seat into the groove. If for some reason you need to remove the insert do NOT grab the lip and try to pull it out. The fit is too tight and you risk tearing the lip of the boot. You need to squeeze the boot from both sides to unseat it from the lip and then gently pry it out. The boots are NOT identical. There is a passenger and driver side so look closely at the labeling on each boot to ensure you insert the correct boot onto the correct side.
2nd Gen 4Runner Double Cup Holder Console Insert
This is a double cup holder for the 2nd gen 4Runner from 1990-1995. It comes with a cell phone slot, 2 cup holders, and 2 pen holders. These are made of ABS plastic from a 3D printer. This mounts inside of the upper storage console. They will come in a black flat finish only. The cup holder will come with 2 strips of 3M automotive adhesive along the bottom if you want to permanently secure it into place but this is not a must. This cup holder will allow the lid to fully close when there are not cups, pens, or phones in it.
BH3D T-Shirt
These t-shirts are made of a very soft durable cotton from Next Level Apparel. They come in a gun metal gray color. It tends to run as a slight “slim” fit meaning it’s a little bit more snug in the shoulders and arms. They are a good long length for men but run a little snug. If you like a loose fitting shirt then I would say order one size up from what you normally where.
Aluminum FJ40 TEQ grille badge
This is a custom machined aluminum TEQ grille badge for an FJ40 Toyota Landcruiser. It comes in two color combos: the red/silver and black/silver It can fit into numerous locations on the grille. This is a two piece design. The backing plate is inserted from the rear and will protrude through the expanded metal grille. You will then run 3 strips of 3M automotive adhesive across the backing plate tabs that will stick out a hair past the grill. The adhesive strips will sandwich the backing plate onto the grille. Once the rear backing plate is securely adhered to the adhesive, you will then remove the red strips to expose the adhesive. The TEQ badge is then stuck onto the adhesive. It has the ability to move up/down and left/right by about 1/2″. Combined with the rear plate’s ability to move all over the grille; you can pretty much put the emblem anywhere you want around the “TOYOTA” emblem on the grille. The pictures provided are all the old plastic version. The new aluminum version will have pics posted soon.