Aluminum 5th Gen 4Runner TEQ Front and Rear Badges
These are machined aluminum TEQ badges for the front grill and rear hatch of the 2009-Present 5th Generation Toyota 4Runner. They come in 3 color options. There is the popular black/silver combo, the retro red/silver combo, and the bare metal for the folks who want to do their own color option. These mount with strips of 3m automotive adhesive on the backside. The factory badge can be removed without even lifting the hood. You simply need a butter knife to pry behind the factory badge and pop it off. There are 3 plastic tabs that hold it on. No screws or adhesive were used to mount the factory badge. My TEQ badge will mount right over the same surface the factory badge was mounted to. Make sure you clean the grill well before sticking the badge on. The rear badge is more difficult to remove. It was installed from the factory with adhesive which will put up a fight before letting go. Be patient with the removal. Good force will be needed to remove it. Also, make sure you line up the badges VERY carefully because once you stick them on they will NOT want to come off.
70 Series Steering Column Insert (pair)
- This is a pair of 3D printed rubber inserts for the steering column of the 70 Series Toyota Landcruiser. This is designed to fill the open hole on the side of the steering column. This does NOT make the steering column waterproof. It is simply to visually give the column a finished look. This design does not require any tools or disassembly of any components. Just slide the boot over the end of the blinker/wiper column and snap it into the hole. This is a very snug fit so you will need to wiggle it into place a bit to properly seat into the groove. If for some reason you need to remove the insert do NOT grab the lip and try to pull it out. The fit is too tight and you risk tearing the lip of the boot. You need to squeeze the boot from both sides to unseat it from the lip and then gently pry it out. The boots are NOT identical. There is a passenger and driver side so look closely at the labeling on each boot to ensure you insert the correct boot onto the correct side.
80/100/LX450/LX470 Rear TEQ Badge (91-07)
This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).
70 Series Landcruiser Turbo Grille badge
This is a machined aluminum “Turbo” badge that mounts to the 70 Series Landcruiser grille. This does NOT fit on all years 70 series cruisers. Please look closely at the pics to ensure the picture matches your grille. This is attached with 3M badge/decal foam adhesive. No screws are needed and no modifications to the factory grille are needed.
70 Series Cruiser Diesel Grille Badge
This is an aluminum diesel badge. It comes it two options. You can order the grille badge that comes with a backing plate pre-attached to allow it to mount flush to the curvature on the grille of the 70 Series Landcruiser OR you can order it without the backing plate as a flat universal mount badge that can be mounted to any flat surface on the vehicle. It has a satin black finish with brushed aluminum raised letters. The OEM screw pegs are not present on our badge so that the badge can mount to 70 series grilles that did NOT come with the holes for mounting. Our badge mounts with 3M automotive badge adhesive. It’s plenty strong to hold the badge for many years without issue as long as the surface is thoroughly cleaned before install. No drilling of the factory grille is needed. Simply peel back the glue backing and stick it on.
3FE “EFI” engine badge
This is a replacement 3FE “EFI” engine badge. It is made of aluminum with a brushed finish and red letters. The letters are painted with high heat fully cured engine enamel. There are 3 options. You can order the engine badge by itself without the high heat adhesive if you already have some at home. You can order the badge WITH a tube of the high heat adhesive. The final option is the EFI FJ40 grille badge (coming soon).
Toyota Pickup (1984-1988) Single Cup Holder
Be aware that there are 4 different consoles that came on the pickup and this insert will only fit one of them. Make sure to look at the pics closely to make sure they match your console. This is a single cup holder for the 84-88 Toyota Pickup. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There are 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
Aluminum Retro “4 Wheel Drive Badge”
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
Cup Holder Ashtray Insert 40 Series 81-84
This is a cup holder that inserts into the ashtray slot on the 1981-1984 Toyota Landcruiser 40 Series. This mounts to the center console and you must have the center console for this to work. It has a 3.25″ top diameter which will accept a majority of drink containers on the market. It also has a small storage cubby at the bottom for loose change or whatever else you want to store in there. This is made of ABS plastic with a satin black finish.
1979-1980+ 40 Series Single Cup Holder
This is a single cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This single cup holder has a hole of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold one cup, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
1st Gen 4runner Cup Holder Console Insert
This is a single cup holder for the 84-89 Toyota 4Runner. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. It also has a cell phone holder slot that is 3.5″ wide which will accept just about every major phone style available. There is a notch at the bottom of the cell phone slot to allow a charging cable to be ran up from the bottom. Be aware you will need to cut a hole in the bottom on the console to be able to run the cable. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There is a countersunk hole at the bottom in case you want to screw it in. That is not a must, just a preference. Any 3/4″- 1″ coarse thread screw will work. There are also 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only. Be aware that there are 4 different consoles that came on the 1st gen 4Runner and this insert will only fit in two of them(which do seem to be the more popular options). Make sure to look at the pics to make sure they match your console.
Aluminum Retro “4 Wheel Drive Badge”
This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.
1984-1988 Pickup Grille Badge
This is the grille badge for the 1984-1988 Toyota Pickup. This will replace the worn out OEM badge which needs to be removed. This is a machined piece of aluminum and a little thicker than the OEM badge. It has a brushed aluminum top finish and comes in 3 background colors of black, red, and the OEM original gold color. The badge has a large strip of 3M automotive badge adhesive on the backside. The grille surface must be cleaned before attaching the new badge.
1st Gen 4Runner Cup Holder (Driver Side)
This is a single cup holder that mounts onto the driver side of the console. It is a standard 3″ diameter hole which will hold the usual fast food cup, soda can, and grocery store water bottle. It will not hold the larger Hydroflasks, Yeti’s, and Nalgene bottles. Our passenger cup holder can do that. The driver side cup holder had to be smaller to account for the drivers leg and shifter levers. This attaches with 2 strips of 3M adhesive and 2 self tapping screws. It is made of ABS plastic with a 3D printer.
62 Series Single Cup Holder Square Insert
This is a single cup holder for the 62 Series Toyota Landcruiser. It will fit snugly into the square hole near the front of the center console. It has a spot for a cup, a cell phone, 2 pens, and a storage slot in the rear. It has a black satin finish and is made of ABS plastic. It comes with 2 strips of 3M automotive adhesive on the bottom to bond it into the hole if desired. No screws or drilling of any kind needed.
80 Series Cup Holder Console Insert
This is a single cup holder that fits snugly into the square hole at the front of most 80 series LandCruisers. The LX450 came with a sub woofer in this hole so this cup holder will only fit in the 91-97 Toyota Landcruiser and not LX450. It has a slot for a cell phone that is the width of the square hole. If your phone fits in the square hole now it will fit with the cup holder installed. The cup holder diameter at the top is 3″ with a slight taper towards the bottom. If you need something larger than 3″ then you will want to buy the single or double cup holder set up that mounts on the side of the shifter console. There are also two pen holders that are tilted forward by 15 degrees to make sure the pens don’t interfere with any cup. Soda cans, water bottles, and all fast food cups all fit without issue. Anything bigger (like a Nalgene bottle) will not. These come in the factory Oak tan color and the dark gray color. These are made of ABS plastic through my 3D printer. Install is simple. Remove the 3M adhesive backing and push it into the hole until it hits bottom. It’s a snug fit so it will take a little force to get it to seat all the way into the bottom. I wanted it to be a snug fit so that if a large cup is put into it with a snug fit, it wont pull the entire insert out when you remove the cup. No screws are needed but I left the factory hole at the bottom available if you decided to run a longer screws and anchor it into place.
3rd Gen 4Runner (96-02) Rear Hatch TEQ Badge
This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.
1980s Retro Toyota “T” badges
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.
Aluminum FJ45 Tailgate Badges
This is a machined aluminum tail gate badge for an FJ45 Toyota Landcruiser. It is designed to be mounted in the oval recessed area on the tailgate. In actuality; it can be mounted on any Toyota on any flat spot, but it was designed to fit perfectly in that oval spot. It is 1/4″ in overall thickness. There are two strips of 3M automotive adhesive that are already attached that will allow you to bond it to the surface. No drilling or hardware is needed for install. Just stick it on. Make sure the surface you are attaching it to is very clean. Put good force onto the emblem when installing it and rock it up and down and left to right to make sure the adhesvie 100% bonds; then hold it firm and in place for about 20 seconds. Also make sure to get it right the first time, because this adhesive doesn’t like to let go once you stick it. I have two color options; the red/silver and black/silver. There is also two design options. You can order the original 4X4 logo or the retro TEQ logo. The picture of the badge installed on the tailgate is the old plastic version. Updated installed pics are coming soon.
Aluminum TEQ Universal Badge (Round and Oval)
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
3rd Gen 4Runner Console Accessory Plate
This is an accessories panel for the 1996-2002 Toyota 4Runner. It mounts to the center console. This is made by a 3D printer from ABS plastic. This will accept OEM Toyota switches from 95-02 and some aftermarket switches. There are two options which is the 4 hole plate and the 2 holes plate. Install instructions will be provided with the packaging. Blank plug inserts can be ordered separately if you want 4 holes but only have 2 accessories so far and don’t want to have an ugly hole for a time period.
Universal 2oz. Hand Sanitizer Holder
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
BH3D Hat (Free with purchase over $100)
This is a BH3D adjustable fit mesh back hat. It's a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.
BH3D Hat (Free with purchase over $100)
This is a BH3D adjustable fit mesh back hat. It’s a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.