- Please choose product options by visiting (91-94) 80 Series Dash Phone Mount.
OUR PRODUCTS
Hilux Surf Double Cup Holder 1996-2002
This is a 3D printed double cup holder for the 1996-2002 Toyota Hilux Surf. This will work on the 4WD automatic console. This will NOT fit on the manual transmission console. That design in still in development. This cup holder is made of ABS plastic and comes in flat black only. This design one large hole with removable snap ring, one smaller hole, and a cell phone slot . The large hole with snap ring removed can accept the newest 36oz. Yeti bottle. With the snap ring in place the cup holder will hold a Nalgene and 32/40oz. Hydroflask. The smaller standard 3″ hole will accept most fast food style containers. This design will hold just about any container on the market. Be aware, this design prevents full forward movement of the passenger seat. The front 3″ of movement will be blocked by the cup holder.
Install Instructions
There are 2 strips of 3M automotive adhesive already attached to help with install. Make sure the surface attaching to is totally clean. Once stuck in place with the adhesive then you will want to use the 2 provided self-taping screws in the side and top hole. Use a hand screw driver and not a power drill so you don’t strip the hole.
70 Series Steering Column Insert (pair)
- This is a pair of 3D printed rubber inserts for the steering column of the 70 Series Toyota Landcruiser. This is designed to fill the open hole on the side of the steering column. This does NOT make the steering column waterproof. It is simply to visually give the column a finished look. This design does not require any tools or disassembly of any components. Just slide the boot over the end of the blinker/wiper column and snap it into the hole. This is a very snug fit so you will need to wiggle it into place a bit to properly seat into the groove. If for some reason you need to remove the insert do NOT grab the lip and try to pull it out. The fit is too tight and you risk tearing the lip of the boot. You need to squeeze the boot from both sides to unseat it from the lip and then gently pry it out. The boots are NOT identical. There is a passenger and driver side so look closely at the labeling on each boot to ensure you insert the correct boot onto the correct side.
89-94 Toyota Pickup Console Cup Holder
This will fit in the 1989-1994 Toyota pickup console. This was mostly offered in the SR5 model. This is 3D printed from ABS plastic. No hardware or tools are needed to install. This will NOT fit in the 4Runner from the same years. That is a different console and we make a different cup holder for the 4Runner console.
1984-1988 Pickup Grille Badge
This is the grille badge for the 1984-1988 Toyota Pickup. This will replace the worn out OEM badge which needs to be removed. This is a machined piece of aluminum and a little thicker than the OEM badge. It has a brushed aluminum top finish and comes in 3 background colors of black, red, and the OEM original gold color. The badge has a large strip of 3M automotive badge adhesive on the backside. The grille surface must be cleaned before attaching the new badge.
70 Series Landcruiser Turbo Grille badge
This is a machined aluminum “Turbo” badge that mounts to the 70 Series Landcruiser grille. This does NOT fit on all years 70 series cruisers. Please look closely at the pics to ensure the picture matches your grille. This is attached with 3M badge/decal foam adhesive. No screws are needed and no modifications to the factory grille are needed.
1979-1983 Toyota Pickup Fender Badge (Universal Fit)
This is a machined aluminum badge with a satin brushed finish on the lettering. This is not a plastic replica like the OEM badge was. This badge is an exact match in size to the original factory badge and mounts with strips of 3M automotive badge/decal adhesive. No drilling of the fenders is needed. The overall length is exactly 10″ (254mm) by 1.4″(36mm) tall. This badge will fit in the factory fender location of the 1979-1983 Toyota pickup BUT it can also mount to any flat surface of any Toyota. It can be mounted on a surface like a flat tailgate of a more modern vehicle giving it that old school retro look.
2015-2020 GMC/Chevy Rear Double Cup Holder
This is a 3D printed rear double cup holder for the 2015-2020 GMC Yukon and Sierra. It also works on the Chevy Suburban, Tahoe, and Silverado for the same years. It mounts to the backside of the center console giving access to the middle row but still accessible from the front row. This is made of ABS plastic with a textured finish coating. It can hold two cups and two pens. There is also a larger round hole to store a flashlight if desired. The inserts are removable to be able to accept large bottles like Hydroflasks, Yeti 36oz bottles, and Nalgene bottles.. It hooks onto the storage compartment on the backside of the center console. This comes with 3M adhesive to permanently attach it if desired. It also has 4 screw holes if you want to bolt it on. The hook by itself will also keep it attached to the console but it can slide a bit left to right and be kicked off by little kids with clumsy feet if you don’t use any adhesive or screws. If you simply use the hook for install then the install time is about 2 seconds. If you choose to use the provided adhesive then you add about 30 seconds to install.
2022 Landcruiser Rear TEQ Badge
This is a rear hatch machined aluminum TEQ badge for the 2022 Toyota Landcruiser (300 Series). The original factory badge will need to be removed. This badge is held on with small strips of 3M automotive badges adhesive. Make sure the suface you are bonding to is clean and you use good force when applying the badge. Hold it in place for 20 seconds to ensure a solid bond.
Universal 2oz. Hand Sanitizer Holder
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
2011-2015 Tacoma TEQ Grille Badge
This aluminum TEQ badge mounts onto the front grille of your 2011-2015 Toyota Tacoma. It replaces OEM part #90975-A2001. The size is 6.25″ x 4.25″ (159mm x 108mm) The factory chrome badge must be removed. The factory mounting holes will not be used on the new badge. To remove the factory badge simply pry it off. It is held on with plastic tabs. No adhesive or screws were used. The new badge is held on with 3M automotive decal adhesive. The surface on the grille the new badge will mount to MUST be cleaned before mounting. This badge comes in the common black/silver color, red/silver color, and in raw metal (no paint or primer) for folks who want to do their own custom paint job.
3rd Gen 4Runner (96-02) Rear Hatch TEQ Badge
This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.
