Show sidebar

Aluminum Retro “4 Wheel Drive Badge”

$32.00$35.00

This is a machined aluminum retro Toyota “4 Wheel Drive” badge. It can be mounted on any flat surface of any Toyota 4×4. It is roughly 4.5″ x 3″ which is the same size as the original Toyota badge. There are 3 color options available. There is the black/silver, cream/silver, and bare aluminum. The black is a satin finish while the cream is a gloss finish. The gloss allowed the cream to stand out a bit more. The bare aluminum is for the folks that want a custom color and are willing to paint themselves. I can also do custom color combos for a couple extra dollars if you let me know what you want. Just send a message regarding your request. These come with 3 strips of 3M automotive adhesive recessed on the backside and ready to install. Make sure the surface you are sticking to if flat and clean.

 

 

Bare Metal
Black & Silver
Cream and Silver

Aluminum TEQ Universal Badge (Round and Oval)

$29.00$35.00

These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.

Oval Bare Aluminum
Oval Black/Silver
Oval Red/Silver
Round Bare Aluminum
Round Black/Silver
Round Red/Silver

Aluminum 5th Gen 4Runner TEQ Front and Rear Badges

$37.00$40.00

These are machined aluminum TEQ badges for the front grill and rear hatch of the 2009-Present 5th Generation Toyota 4Runner. They come in 3 color options. There is the popular black/silver combo, the retro red/silver combo, and the bare metal for the folks who want to do their own color option. These mount with strips of 3m automotive adhesive on the backside. The factory badge can be removed without even lifting the hood. You simply need a butter knife to pry behind the factory badge and pop it off. There are 3 plastic tabs that hold it on. No screws or adhesive were used to mount the factory badge. My TEQ badge will mount right over the same surface the factory badge was mounted to. Make sure you clean the grill well before sticking the badge on. The rear badge is more difficult to remove. It was installed from the factory with adhesive which will put up a fight before letting go. Be patient with the removal. Good force will be needed to remove it. Also, make sure you line up the badges VERY carefully because once you stick them on they will NOT want to come off.

Bare Metal Front Grill
Bare Metal Rear Hatch
Black/Silver Front Grill
Black/Silver Rear Hatch
Red/Silver Front Grill
Red/Silver Rear Hatch

80/100/LX450/LX470 TEQ grill badge

$40.00

This machined aluminum TEQ badge mounts onto the front grille of your a 91-94 & 95-97 Toyota LandCruiser (80 series) and the 98-07 (100 series). WIll also mount to the LX450 and LX470 Lexus. I offer the badge in the retro red/silver, the black/silver, and bare aluminum for the folks who want to do there own paint color. The factory chrome “sombrero” must be removed. For the 95-02 Cruiser and LX TEQ badge the easiest way to install the emblem is to remove the entire grill and then install the emblem. This is not a must. You can use a stubby screwdriver and pliers, but you will need some patience and a cool car; NOT a hot radiator. Don’t forget to remove the backing from the 3M adhesive. You want to run the screws through the backside of the grill first. Make SURE to use the provided black washers between the screws and backside of the grill. They are for spacing purposes to get the TEQ badge perfectly flat to your grill. Once the screws are through then start each screw with a full turn but prevent the adhesive from grabbing the grill Do not tighten the screws until all of them have been started. That will ensure you get everything lined up properly. Once the screws have threaded in slightly then you can press the badge onto the grill and the adhesive will hold it nice and snug while you screw in the 3 screws. Between the adhesive and screws everything should stay nice and flush. Reinstall the grille in the same way you removed it. IF you are buying the 03-07 badge then there were no screws used on the OEM sombrero badge. Toyota only used adhesive. You will need to pry the factory badge off. Some heat and fishing line will help. There are small tabs that help center the badge so you will not be able to simply run the fishing line all the way down the back side. Once the badge and adhesive are removed, you will simply stick the new badge on using the same type of 3M adhesive. No hardware needed for the 03-07 badge and no need to remove the grill.

80/100/LX450/LX470 Rear TEQ Badge (91-07)

$36.00$40.00

This is an aluminum TEQ emblem for the rear hatch of all years 80 and 100 series (LX and YOTA). It has a brushed finish on the letters and outer ring. This badge can replace the factory “sombrero” or “L” OR can be mounted to either side. There is a curvature on the back that matches the curvature of the rear hatch. The emblem can be slid left or right of the factory emblem but not up or down. To attach, you will use two strips of 3M automotive adhesive (provided and already attached) Make sure to take your time when installing because once you install, the adhesive doesn’t like to let go. Make sure the surface is clean and you use good force to adhere the emblem. Also hold it in place with good pressure for about 20 seconds to ensure a good bond. The factory emblem was installed with automotive adhesive as well and has been on therir for 17+ years so anticipate a little battle to get it off. A heat gun will help but don’t use too much heat and damage the paint. A flat head screw driver and razor blade is also helpful but be VERY careful not to gouge your paint in the process. This comes in the black/silver (satin finish) or the retro red/silver option (gloss finish).

100 Series Bare Metal
100 Series Black/Silver
100 Series Red/Silver
80 Series Bare Metal
80 Series Black/Silver
80 Series Red/Silver

1st Gen 4Runner/Surf B-Pillar Badge

$27.00$55.00

This is a replacement B-Pillar badge for the 1984-1989 Toyota 4Runner. It will replace the faded clear plastic OEM badge. This is made of aircraft grade aluminum. It has 2 strips of 3M automotive adhesive on the back side for securing. Once you pop off the original OEM badge you need to clean the surface behind it so the new badge will bond well. This is available in the black/silver, red/silver, and raw metal for folks who want to do their own custom color.

Black Pair 4Runner
Black Pair Surf
Black Single 4Runner
Black Single Surf
Raw Metal Pair 4Runner
Raw Metal Pair Surf
Raw Metal Single 4Runner
Raw Metal Single Surf
Red Pair 4Runner
Red Pair Surf
Red Single 4Runner
Red Single Surf

Aluminum FJ45 Tailgate Badges

$29.00$32.00

This is a machined aluminum tail gate badge for an FJ45 Toyota Landcruiser. It is designed to be mounted in the oval recessed area on the tailgate. In actuality; it can be mounted on any Toyota on any flat spot, but it was designed to fit perfectly in that oval spot. It is 1/4″ in overall thickness. There are two strips of 3M automotive adhesive that are already attached that will allow you to bond it to the surface. No drilling or hardware is needed for install. Just stick it on. Make sure the surface you are attaching it to is very clean. Put good force onto the emblem when installing it and rock it up and down and left to right to make sure the adhesvie 100% bonds; then hold it firm and in place for about 20 seconds. Also make sure to get it right the first time, because this adhesive doesn’t like to let go once you stick it. I have two color options; the red/silver and black/silver. There is also two design options. You can order the original 4X4 logo or the retro TEQ logo. The picture of the badge installed on the tailgate is the old plastic version. Updated installed pics are coming soon.

bare metal 4x4
bare metal TEQ
black/silver 4x4
black/silver TEQ
red/silver 4x4
red/silver TEQ

1979-1983 Toyota Pickup Fender Badge (Universal Fit)

$40.00

This is a machined aluminum badge with a satin brushed finish on the lettering. This is not a plastic replica like the OEM badge was. This badge is an exact match in size to the original factory badge and mounts with strips of 3M automotive badge/decal adhesive. No drilling of the fenders is needed. The overall length is exactly 10″  (254mm) by 1.4″(36mm) tall. This badge will fit in the factory fender location of the 1979-1983 Toyota pickup BUT it can also mount to any flat surface of any Toyota. It can be mounted on a surface like a flat tailgate of a more modern vehicle giving it that old school retro look.

3rd Gen 4Runner (96-02) Rear Hatch TEQ Badge

$28.00$30.00

This is an aluminum rear hatch TEQ badge that will replace the factory Toyota logo. This will fit on the rear hatch of any 1996-2002 Toyota 4Runner. It matches the subtle curvature of the rear hatch of the 3rd Gen 4Runner specifically. This badge comes in black or red with a brushed aluminum raised trim. It will come with 2 recessed strips of 3M automotive decal adhesive for install. Make sure the surface is clean when installing. To remove the old factory badge you need something like a butter knife or flat head screw driver to pry it off. There are two plastic tabs that help center the factory badge that need to be fully pulled out. The glue should be off with medium force. If it does not, a blow drier or heat gun can heat it up and soften it and make removal a bit easier.

Unpainted Raw Metal
Black & Silver
Red & Silver

Aluminum FJ40 TEQ grille badge

$40.00

This is a custom machined aluminum TEQ grille badge for an FJ40 Toyota Landcruiser. It comes in two color combos: the red/silver and black/silver It can fit into numerous locations on the grille. This is a two piece design. The backing plate is inserted from the rear and will protrude through the expanded metal grille. You will then run 3 strips of 3M automotive adhesive across the backing plate tabs that will stick out a hair past the grill. The adhesive strips will sandwich the backing plate onto the grille. Once the rear backing plate is securely adhered to the adhesive, you will then remove the red strips to expose the adhesive. The TEQ badge is then stuck onto the adhesive. It has the ability to move up/down and left/right by about 1/2″. Combined with the rear plate’s ability to move all over the grille; you can pretty much put the emblem anywhere you want around the “TOYOTA” emblem on the grille. The pictures provided are all the old plastic version. The new aluminum version will have pics posted soon.

70 Series Cruiser Diesel Grille Badge

$32.00$35.00

This is an aluminum diesel badge. It comes it two options. You can order the grille badge that comes with a backing plate pre-attached to allow it to mount flush to the curvature on the grille of the 70 Series Landcruiser OR you can order it without the backing plate as a flat universal mount badge that can be mounted to any flat surface on the vehicle. It has a satin black finish with brushed aluminum raised letters. The OEM screw pegs are not present on our badge so that the badge can mount to 70 series grilles that did NOT come with the holes for mounting. Our badge mounts with 3M automotive badge adhesive. It’s plenty strong to hold the badge for many years without issue as long as the surface is thoroughly cleaned before install. No drilling of the factory grille is needed. Simply peel back the glue backing and stick it on.