70 Series Cruiser Diesel Grille Badge
This is an aluminum diesel badge. It comes it two options. You can order the grille badge that comes with a backing plate pre-attached to allow it to mount flush to the curvature on the grille of the 70 Series Landcruiser OR you can order it without the backing plate as a flat universal mount badge that can be mounted to any flat surface on the vehicle. It has a satin black finish with brushed aluminum raised letters. The OEM screw pegs are not present on our badge so that the badge can mount to 70 series grilles that did NOT come with the holes for mounting. Our badge mounts with 3M automotive badge adhesive. It’s plenty strong to hold the badge for many years without issue as long as the surface is thoroughly cleaned before install. No drilling of the factory grille is needed. Simply peel back the glue backing and stick it on.
1980s Retro Toyota “T” badges
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.
1st Gen 4Runner Single Cup Holder (rare console)
This is a single cup holder for the later years 1st Gen 4Runner. This console was not standard and is much more rare in 1st Gens. Look CLOSELY at the pictures to make sure this is the console you have before buying. This cup holder is made of ABS plastic through the use of a 3D printer. It has a slot for a cup, a phone, and 2 pens. It will come with 2 strips of 3M adhesive for attachment and one self tapping screw for added stability if desired.
Ashtray 40 Series 81-84+
This is an ashtray for the rear ashtray hole on the 1981-1984 40 Series Landcruiser center console. This is designed to look very similar to the OEM design but not identical. The original OEM design had numerous structural issues leading to cracking in numerous places. Those structural issues have been addressed in this design. It will still fit, look, and function like the OEM design. The hinge hardware has also been reinforced to be much more robust then the OEM slide pegs that were originally used. There are pressed fit and hidden nuts under the hinge with countersunk hardened black bolts. The original OEM metal plate spring is NOT included with this cup holder. The updated hardware gives the lid a stiffer movement which removes the need for the metal plate spring. The recessed area is still in this design to accept the OEM plate spring if you decide you want the look of it. This is made of ABS plastic with a black satin finish.
70 Series Cup Holder-Go to Odd Iron Offroad For Purchasing-Link Below
Now sold at our vendor site at http://www.oddironoffroad.com/store#!/70-Series-Cup-Holders-by-BH3D/p/82522362/category=23176020
This is a double cup holder for the 70 series landcruiser. This cup holder has a slot for 2 drinks, 2 pens, a cell phone, and a slot for a multi-tool or knife. It comes in a flat black finish. There are two versions. Both designs will work on either the RHD or LHD variants. Both have the some shape/functions up top but mount very differently. One cup holder is for the 70 series that came with a center console that goes up and around the shifters. It will mount up on top of the consoles and will come with 6 strips of 3M adhesive to secure it. It also has screw holes that will line up with the factory screw holes if you want to screw it down. You will need to source the screw. This cup holder can be flipped 180 degrees to go on either the RHD or LHD. The other double cup holder mounts to the floor of the 70 series landcruiser. It will also come with strips of 3M adhesive. That alone with not be adequate for attachment. You will need to screw the floor mounted cup holder into the floor. 2 self taping screws will be provided for that model. There are two countersunk holes at the bottom of this cup holder to guide you in placement of the screws. These cup holders are 3D printed and made of ABS plastic. I can do certain custom colors upon request. I have color matches in brown and gray for certain years/models 70 series but not all.
Aluminum FJ Cruiser TEQ Badge
This is a brushed aluminum TEQ badge that can be mounted on all years FJ Cruisers and can be mounted in numerous locations on the upper and lower grille. The backing plate is installed from the rear of the grille. Provided strips of 3m automotive adhesive are already installed on the back of the emblem. You simply need to remove the red backing from the tape and stick the emblem onto the backing plate. Use good force when installing the adhesive. The install should take 1-2 minutes tops. No tools are needed. This adhesive is VERY sticky so make sure you line it up and get it straight before you stick it on. You probably want someone to hold the backing plate in place while you install the TEQ badge so you can be directly in front and level with the badge as you install it to guarantee you get it straight. I have the black/silver, red/silver, and bare aluminum in stock. The bare aluminum would be for the folks looking to color match their paint.
3FE “EFI” engine badge
This is a replacement 3FE “EFI” engine badge. It is made of aluminum with a brushed finish and red letters. The letters are painted with high heat fully cured engine enamel. There are 3 options. You can order the engine badge by itself without the high heat adhesive if you already have some at home. You can order the badge WITH a tube of the high heat adhesive. The final option is the EFI FJ40 grille badge (coming soon).
1979-1980+ 40 Series Double Cup Holder
This is a double cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has holes of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold two cups, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
2011-2015 Tacoma TEQ Grille Badge
This aluminum TEQ badge mounts onto the front grille of your 2011-2015 Toyota Tacoma. It replaces OEM part #90975-A2001. The size is 6.25″ x 4.25″ (159mm x 108mm) The factory chrome badge must be removed. The factory mounting holes will not be used on the new badge. To remove the factory badge simply pry it off. It is held on with plastic tabs. No adhesive or screws were used. The new badge is held on with 3M automotive decal adhesive. The surface on the grille the new badge will mount to MUST be cleaned before mounting. This badge comes in the common black/silver color, red/silver color, and in raw metal (no paint or primer) for folks who want to do their own custom paint job.
Universal 2oz. Hand Sanitizer Holder
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.
Toyota Pickup (1984-1988) Single Cup Holder
Be aware that there are 4 different consoles that came on the pickup and this insert will only fit one of them. Make sure to look at the pics closely to make sure they match your console. This is a single cup holder for the 84-88 Toyota Pickup. This is made of ABS plastic by a 3D printer. It has a 3″ diameter hole which will hold most beverage containers on the market. There are also two holes to accept pens and a small storage compartment in the back for whatever you can stick in there. There are 2 strips of 3M automotive adhesive on the bottom if you want to glue it into place. This comes in a satin black finish only.
1st Gen 4Runner Cup Holder (Driver Side)
This is a single cup holder that mounts onto the driver side of the console. It is a standard 3″ diameter hole which will hold the usual fast food cup, soda can, and grocery store water bottle. It will not hold the larger Hydroflasks, Yeti’s, and Nalgene bottles. Our passenger cup holder can do that. The driver side cup holder had to be smaller to account for the drivers leg and shifter levers. This attaches with 2 strips of 3M adhesive and 2 self tapping screws. It is made of ABS plastic with a 3D printer.