Showing all 14 results
These are machined Aluminum TEQ badges (NOT PLASTIC) that can be mounted to any year and model Toyota/Lexus on any flat surface. It comes in 2 options. You can order the round or oval TEQ badge. Each badge comes in 3 finishes. You can get the red/silver, black/silver, and bare metal. The black/silver has a satin finish. The red/silver has a gloss finish. Just seemed to look best in those two finishes for those specific colors. The bare metal is for folks who want to paint them with your own custom color. Just do a couple heavy coats and then give 48 hours of drying time. Get some fine grit sandpaper and sand off the outer edge exposing the aluminum on the letters. The round is 3.5″ in diameter. The oval is 3.5″ tall and 5.2″ wide. These come with 3 strips of 3M automotive adhesive already installed. When installing make sure the surface is clean. Make sure you take your time to get it right. Once it’s stuck on, it does NOT want to come off.
This is an aluminum retro “Turbo” badge. This is inspired by the “Turbo” badge Toyota made in the 1980s. It can mount to any flat surface on the vehicle. Will come with 1-2 strips (depending on size) of 3M automotive adhesive to mount to the vehicle. There are 2 sizes and two color options for each size for a total of 4 options. There is the 7″ and 5″ black/silver badges. There is also the 7″ and 5″ black/silver/red badges.
This is a Universal Aluminum TEQ/Diesel badge for a Toyota. The lettering is inspired by the Diesel font used by Toyota throughout the early 80s to late 90s. This is designed to mount on any flat smooth surface on the vehicle. It comes with strips of 3M automotive adhesive on back for attachment.
These t-shirts are made of a very soft durable cotton from Next Level Apparel. They come in a gun metal gray color. It tends to run as a slight “slim” fit meaning it’s a little bit more snug in the shoulders and arms. They are a good long length for men but run a little snug. If you like a loose fitting shirt then I would say order one size up from what you normally where.
This is a double cup holder for a 1981-1984+ FJ40 Toyota Landcruiser. This console was also offered in years after 1984 in some markets. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has two different sized holes to accept all types of cups. This can hold the usual fastfood cup, coffee cups with handles, and even the large yeti 40oz cups with ease. The cup holder also has a slot for an LED flashlight, a slot for a knife/multi tool, and two pend slots. Along the one side there is room to hold two cell phones as well. This will come with 2 strips of 3M automotive adhesive on bottom in case you want to permanently attach it to the console but that is not required for install. No hardware or tools are needed for install.
This is a BH3D adjustable fit mesh back hat. It’s a charcoal gray color. This hat is built Richardson and is their Type 112 hat built to last. If you spend over $100 on our website then the hat is free.
Use Coupon code “Free Hat” during checkout once you have added at least $100 of product into the cart. Also, make sure you actually add the hat into the cart first.
This is a double cup holder insert for the stamped metal center console of a 1973-1978 Toyota Landcruiser. This is made of ABS plastic with a 3d printer. It will come with a smooth flat black finish. This cup holder has holes at 3.25″ diameter to accept large fast food cup type drinks and the 30/40 oz yeti type thermos. It will also hold smaller containers securely. This insert also has two slots for pens, a slot for a knife/multi-tool, a slot for an LED flashlight and still leave a 1.2″ slot in the rear for a cell phone or wallet. It will allow that awkward hole to have good functional use of the space. There will be 2 strips of 3M automotive adhesive on the bottom in case you want to permanently secure it to the bottom of the console. This is not needed for install. No hardware needed.
These are Retro Toyota “T” logos inspired from Toyota logos used in the early 80s. Instead of chrome plastic we went with a more modern brushed aluminum. There are 2 versions. Version #1 is a bit larger at 4″ tall by 3 1/4″ wide. Versioni #2 is 3 3/8″ x 3 1/4″ wide. These are a bit larger than the original OEM badges. They both come with 2 strips of 3M automotive adhesive on back in case you want to stick it on. They will mount to any flat surface on our vehicle. They also come with screws and washers and pre-existing threaded holes in case you want to attach with screws. You do NOT need to use both forms of attachment.
This is an ashtray for the rear ashtray hole on the 1981-1984 40 Series Landcruiser center console. This is designed to look very similar to the OEM design but not identical. The original OEM design had numerous structural issues leading to cracking in numerous places. Those structural issues have been addressed in this design. It will still fit, look, and function like the OEM design. The hinge hardware has also been reinforced to be much more robust then the OEM slide pegs that were originally used. There are pressed fit and hidden nuts under the hinge with countersunk hardened black bolts. The original OEM metal plate spring is NOT included with this cup holder. The updated hardware gives the lid a stiffer movement which removes the need for the metal plate spring. The recessed area is still in this design to accept the OEM plate spring if you decide you want the look of it. This is made of ABS plastic with a black satin finish.
This is a double cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This double cup holder has holes of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold two cups, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
This is a cup holder that inserts into the ashtray slot on the 1981-1984 Toyota Landcruiser 40 Series. This mounts to the center console and you must have the center console for this to work. It has a 3.25″ top diameter which will accept a majority of drink containers on the market. It also has a small storage cubby at the bottom for loose change or whatever else you want to store in there. This is made of ABS plastic with a satin black finish.
This is a single cup holder for a 1979-1980+ FJ40 Toyota Landcruiser. This console was also offered in years after 1980 in FJ40s without the rear heat. This is made of ABS plastic from a 3D printer. It will come in a smooth flat black finish. This single cup holder has a hole of 3.25″ to allow for large drinks containers and the 30/40 oz. yeti type thermos. This cup holder will hold one cup, two pens, and a cell phone. It will come with strips of 3M automotive adhesive under the cup holder in case you want to permanently attach it to the console but that is not required for install. No hardware needed.
This is a machined aluminum badge with a satin brushed finish on the lettering. This is not a plastic replica like the OEM badge was. This badge is an exact match in size to the original factory badge and mounts with strips of 3M automotive badge/decal adhesive. No drilling of the fenders is needed. The overall length is exactly 10″ (254mm) by 1.4″(36mm) tall. This badge will fit in the factory fender location of the 1979-1983 Toyota pickup BUT it can also mount to any flat surface of any Toyota. It can be mounted on a surface like a flat tailgate of a more modern vehicle giving it that old school retro look.
This is a 3D printed 2oz. Hand Sanitizer bottle holder. It is made from ABS plastic. It will hold most major brands of 2oz. hand sanitizer bottles. It comes with 3 strips of 3M automotive adhesive. Some of the brands it holds are shown in picture 5 but there are more. This holder can be stuck to any flat surface in your car, shop, work space, garage, kitchen, etc. Make sure the surface you stick it to has been thoroughly cleaned first. You can order this holder with 1, 2, or 3 bottles of hand sanitizer.